Definition of IEC Power Cables and the Benefits of IEC Cabling Usage
You require to line up the post on the coupler with the holes in the rubber piece. When this is done, put the clips back on the motor and reinsert the screws. Now you can plug the harness to the motor and re-install the clips that hold the pump to the motor.
After you have actually loosened up the panel, all you do is lift it up and let it rest over the back panel of the washer. Roll the control panel back over the cabinet and re-install the clips or screws.
The most typical control panel is held in location to the cabinet with 2 screws at the base of the panel, on the right and left edge. The latest style is that there are spring design clip under the end caps of the control panel. You require to press the tool under the end caps and raise the control panel.
The most typical control panel is held in location to the cabinet with 2 screws at the base of the panel, on the right and left edge. The latest style is that there are hydraulic-coupler-excavator-attachments spring design clip under the end caps of the control panel. You require to press the tool under the end caps and raise the control panel.
After you have actually loosened up the panel, all you do is lift it up and let it rest over the back panel of the washer. To do this, you require to find a spring clip on the external edge of the top of the cabinet. Next you require to take the screws out of the clips that hold the motor to the transmission and eliminate the clips utilizing a basic screw chauffeur.
After the control board is locked down, plug the washer back in and attempt the spin cycle. After you make sure the spin cycle is working, attempt the wash cycle and make certain it is okay. Now you are ready to do the wash and take pride in what you have actually performed in fixing your washer.
Tools you will require are: 1/4″ or 5/16″ socket or nut motorist, basic screw chauffeur, little hammer, 1/2″ socket with extension, pliers.
Press the front on the cabinet under the front edge of the frame and then let the cabinet fall towars the back panel. If the side are bowing out, one side at a time you require to press the rear edge of the panel inward and lock on the frame. Roll the control panel back over the cabinet and re-install the clips or screws.
You require to line up the post on the coupler with the holes in the rubber piece. When this is done, put the clips back on the motor and reinsert the screws. Now you can plug the harness to the motor and re-install the clips that hold the pump to the motor. After you have actually loosened up the panel, all you do is lift it up and let it rest over the back panel of the washer. Roll the control panel back over the cabinet and re-install the clips or screws. The most typical control panel is held in location to the cabinet with 2 screws at the base of the panel, on the right and left edge. The latest style is that there are spring design clip under the end caps of the control panel. You require to press the tool under the end caps and raise the control panel. The most typical control panel is held in location to the cabinet with 2 screws at the base of the panel, on the right and left edge. The latest style is that there are hydraulic-coupler-excavator-attachments spring design clip under the end caps of the control panel. You require to press the tool under the end caps and raise the control panel. After you have actually loosened up the panel, all you do is lift it up and let it rest over the back panel of the washer. To do this, you require to find a spring clip on the external edge of the top of the cabinet. Next you require to take the screws out of the clips that hold the motor to the transmission and eliminate the clips utilizing a basic screw chauffeur. After the control board is locked down, plug the washer back in and attempt the spin cycle. After you make sure the spin cycle is working, attempt the wash cycle and make certain it is okay. Now you are ready to do the wash and take pride in what you have actually performed in fixing your washer. Tools you will require are: 1/4″ or 5/16″ socket or nut motorist, basic screw chauffeur, little hammer, 1/2″ socket with extension, pliers. Press the front on the cabinet under the front edge of the frame and then let the cabinet fall towars the back panel. If the side are bowing out, one side at a time you require to press the rear edge of the panel inward and lock on the frame. Roll the control panel back over the cabinet and re-install the clips or screws.